Hem > spellista
If you're looking for a great grinding ball to use in your kvarnslipmaskin, you've come to the right place! We have a wide selection of forged steel, tungsten carbide and ceramic balls to choose from.
Härdat stål slipande bollar are used in a lot of different places, from gold mines to coal-fired power plants. These balls are made from alloy steels of high quality. They come in many different grades and sizes. A Scale is used to figure out how hard a forged ball is. The ore being ground changes how hard a steel ball is. Good is a forged ball with a core hardness between 50 and 55 and a surface hardness between 55 and 62. Forged steel balls are often made from stainless steel and alloys of stainless steel. The ball can be tempered to make it more resistant to wear and tear from impact. This makes production go more smoothly. It is also the cheaper choice. In order to make forged steel balls, you have to heat and cool them. When the temperature is high enough, the ball's internal stress can't break it. Different carbon, iron, and chromium alloys can be used to make balls that have been forged. With more chromium, the hardness can be made to be higher.
Kiselnitrid slipbolls are used for a variety of applications. Their high-wear and oxidation-resistance properties make them suitable for high-impact applications. They are also able to handle hot, corrosive environments. When it comes to the sintering process of silicon nitride, sintering additives can greatly affect the final product. These additives are used to achieve dense microstructures of the ceramic material. Some of these additives include magnesium silica nitrogen (MgO), al2O3, and Y2O3. Sintering aids are important because they promote the reorganization of the powder particles into a liquid phase. In the liquid phase, the particles are supported by osmotic repulsion. This type of slurry has a high solid-phase volume fraction. The amount of the particles in the suspension can reach 60%. The process of preparing silicon nitride granules is labor intensive. For this reason, it can be difficult to produce a consistent quality product. A solution to this problem is the application of a spray drying technique. Spray-dried powders have a narrow size distribution, good fluidity, and excellent flowability.
One of the hardest and densest types of milling balls is made of tungsten carbide. They are also known for their excellent ability to resist wear and corrosion. Grinding media made of tungsten carbide come in a range of sizes and shapes. There are many different industrial uses for these balls. Their high specific gravity and hardness make them resistant to wear, and most metal powders can be crushed with them. The balls come in a variety of shapes, such as balls, jars, and other tools. Most of the time, they come in packs of 25. In the past, steel was used to make slipkulor för kulkvarn.But there are things that are more recent. Silicon carbide and zirconium oxide are two popular alternatives. Silicon nitride balls are among the most expensive. They are made to grind the same things as tungsten carbide balls. Zirconium oxide satellites, on the other hand, are cheaper and more uniform. When it comes to corrosion, tungsten carbide grinding balls are better than 440C stainless steel balls. They also have a magnetic pull. With 440C stainless steel media, they can be used for many different things.
Ceramic grinding balls are a type of grinding media that are used to make many different things. These balls have a lot of alumina in them, don't have pores, and can last a long time. They are also very resistant to wear and tear. They are often used in ball mills, which are cylinder-shaped machines that grind things into small pieces. Attrition is the name for this process. Earlier, grinding media was made from steel. But now, there are many different kinds of media to choose from. The most common type of media is made of alumina keramiska slipkulor. They are very tough and hard, so they can be used in places where high efficiency and low wear are needed. Alumina powder is burned in tunnel kilns at high temperatures to make alumina ceramic grinding balls. There are different sizes of these balls. Usually, they come in three different sizes. Most of the time, they are between 0.5mm and 120mm in diameter. Even though these are the standard sizes, they can be changed to fit different needs.
Tencan has its own manufacturing center with an area of 20,000 square meters and an R&D center of 22,000 square meters.Tencan has 5 product series including more than 40 models and more than 400 kinds of spare parts and accessories that meet all customers' needs in all respects. Tencan has been granted more than 30 patents, and has a partnership with 20 medical doctors from five well-known universities.
The company's core business is powder equipment manufacture technology, as well as powder materials such as kulkvarnspulver. Our main products currently comprise all types of laboratory ball mills, planetary ball mills, crushing and milling machines screening, mixing and screening equipment, aswell as other lab equipment such glove boxes, scientific research equipment, and other equipment.
The company is certified ISO9001 quality management system, CE, SGS, as and other certifications for systems. Additionally it has acquired more than 40 core patented technology with independent intellectual properties rights. It is recognized as a "high-tech enterprise in Hunan Province" by the government.
The primary customers include universities, research centers as well as technology-based companies. They provide more than 20,000 clients around the world and export to more than 60 countries.
EN 
NL
FR
DE
HI
IT
KO
PL
PT
RU
ES
TR
AR
BG
HR
CS
DA
FI
EL
JA
NO
RO
SV
IW
ID
LV
LT
SR
SK
SL
UK
VI
ET
HU
UZ
TH
FA
MS
BE
HY
AZ
KA
MN
MY
KK
TG
